We ship only once per week (see FAQ)!
sysmocom webshop CLOSED (moving office) April 6 - 20, 2024!
Only UPS shipping available
sysmocom webshop CLOSED (moving office) April 6 - 20, 2024!
Filter
SMA Attenuator, DC to 6 GHz, 500mW, 20dB
This is a SMA in-line (male-to-female) connectorized attenuator for 0-6GHzThe attenuator supports a maximum power of 500mW and is specified for 20 dB +/- 0.3dB over the temperature range of -45 to 100 centigrade.Ideal for use as component in RF networks for direct connection of phones to a BTS, without any air interface.

€24.99*
SMA Attenuator, DC to 6 GHz, 500mW, 30dB
This is a SMA in-line (male-to-female) connectorized attenuator for 0-6GHzThe attenuator supports a maximum power of 500mW and is specified for 30 dB +/- 0.3dB over the temperature range of -45 to 100 centigrade.Ideal for use as component in RF networks for direct connection of phones to a BTS, without any air interface.

€29.75*
SMA Terminator, 50 Ohms, 1W
This is a SMA (male) plug with integrated 50 Ohms resistive terminator.The terminator can sink up to 1W of RF power.Minimum return loss for GSM 850/900: 46 dB, for GSM 1800/1900: 39 dB.

€23.80*
42.5dB IL resistive 1:4 RF splitter/combiner/attenuator PCBA, U.FL in, SMA out
This is a 1:4 resistive RF splitter/combiner with on-board additional per-port 30dB attenuation, resulting in total insertion loss of 42.5 dB.see the product homepage for more details, including the data sheet

€59.50*
12.5dB IL resistive 1:4 RF splitter/combiner PCBA, U.FL in, SMA out
This is a 1:4 resistive RF splitter/combiner, resulting in total insertion loss of 12.5 dB.see the product homepage for more details, including the data sheet

€35.70*
52.5dB IL resistive 1:4 RF splitter/combiner/attenuator PCBA, U.FL in, SMA out
This is a 1:4 resistive RF splitter/combiner with on-board additional per-port 40dB attenuation, resulting in total insertion loss of 52.5 dB.see the product homepage for more details, including the data sheet

€59.50*
4-channel RF Digital Step Attenuator (0..62dB)
BGT-KOH: Desktop Enclosure
The sysmoRFDSATT family is a product family of digitally controlled / programmable RF step attenuators. The initial product within this family is the sysmoRFDSATT-4-62 with: 4 independent RF channels 0 .. 62 dB nominal attenuation per channel. This kind of device can be very useful in any kind of laboratory or test setup where RF signal strength must be adjusted programmatically. A classic use case is e.g. the testing of power-based hand-over within lab setups of cellular radio network, such as GSM BTS, UMTS NodeB, LTE eNodeB or 5G gNodeB.Note: No power supply nor serial cable included (please order separately if needed: power supply, serial cable) Form-Factors The sysmoRFDSATT-4-62 is available in three variants: PCBA only, for integration into custom projects 3U Component Carrier Desktop Enclosure Software Integration The full firmware stack, from boot loader up to the application firmware is Open Source Software. This means any user can be modified to accommodate any specific requirements. For example, the following modifications are easily possible: support of the SCPI protocol for integration into existing lab software solutions support of any application-specific control protocol support of autonomous execution of entire scenarios, like ramping attenuation with certain slopeFurther ReadingProduct HomepageData Sheet

€440.30*
4-channel RF Digital Step Attenuator (0..62dB)
BGT-KOH: 3U component carrier module
The sysmoRFDSATT family is a product family of digitally controlled / programmable RF step attenuators. The initial product within this family is the sysmoRFDSATT-4-62 with: 4 independent RF channels 0 .. 62 dB nominal attenuation per channel. This kind of device can be very useful in any kind of laboratory or test setup where RF signal strength must be adjusted programmatically. A classic use case is e.g. the testing of power-based hand-over within lab setups of cellular radio network, such as GSM BTS, UMTS NodeB, LTE eNodeB or 5G gNodeB.Note: No power supply nor serial cable included (please order separately if needed: power supply, serial cable) Form-Factors The sysmoRFDSATT-4-62 is available in three variants: PCBA only, for integration into custom projects 3U Component Carrier Desktop Enclosure Software Integration The full firmware stack, from boot loader up to the application firmware is Open Source Software. This means any user can be modified to accommodate any specific requirements. For example, the following modifications are easily possible: support of the SCPI protocol for integration into existing lab software solutions support of any application-specific control protocol support of autonomous execution of entire scenarios, like ramping attenuation with certain slopeFurther ReadingProduct HomepageData Sheet

€440.30*