We ship only once per week (see FAQ)!
welcome to the sysmocom webshop!
Only UPS shipping available
welcome to the sysmocom webshop
Radio Frequency
Filter
868 (863..870) MHz cavity filter (ISM, LoRa, SigFox, Helium)
Data SheetThis is a cavity filter for the 868 MHz ISM band, used by LoRA, SigFox and many other narrow-band IoT technologies.You can use it to attenuate any out-of-band interference. It will attenuate transmissions from nearby cellular band.Both connectors are SMA (female). It is not suitable for outdoor environments.It can support up to 30W of RF power and has the following characteristics: 868 MHz ISM Cavity FilterPass Band863 - 870 MHzInsertion Loss<= 1.0 dBPassband Ripple0.2 dBRejection>= 40 dB @ 833 MHz; >= 44 dB @ 903 MHzVSWR<= 1.20Impedance50 OhmsPower30 W average RF power (max)Temperature-10 to 50 CentigradeDimensions54x54x45 mmWeight220 gIP-RatingIP50

€53.55*
1090 MHz cavity filter for Mode-S / ADS-B
Data SheetThis is a cavity filter for 1090 MHz Mode-S / ADS-B.You can use it to attenuate any out-of-band interference while receiving ADS-B / Mode-S. It will attenuate any transmissions from the nearby 900 MHz GSM band by 80 dB.Both connectors are SMA (female). It is not suitable for outdoor environments.It can support up to 30W of RF power and has the following characteristics: 1090 MHz ADS-B Cavity FilterPass Band1086 - 1094 MHzInsertion Loss<= 1.0 dBPassband Ripple0.2 dBRejection80 dB @ 921-960 MHz (GSM 900)VSWR<= 1.20Impedance50 OhmsPower30 W average RF power (max)Temperature-10 to 50 CentigradeDimensions54x54x45 mmWeight200 gIP-RatingIP50

€47.60*
SMA-male to SMA-male cable, RG402, rigid-flex, 20cm
This is a 20cm rigid-flex coaxial cable, RG402 type, terminated with male SMA connectors at both ends.Rigid-flex cables have outstanding screening efficiency compared to normal coaxial cabling, making them ideal in all applications requiring maximum isolation from the external RF environment, such as in test setups for mobile communications.

€5.95*
L-Band cavity filter 1525-1705 MHz
Data sheetThis is a cavity band-pass filter for the 1525-1705 MHz L-Band, particularly useful in satellite receiver applicationsYou can use it to attenuate any out-of-band interference while receiving only the wanted band. It will attenuate any transmissions from the nearby 1700/1800 MHz GSM band by >= 50 dB.Both connectors are SMA (female).It is not suitable for outdoor environments.It can support up to 30W of RF power and has the following characteristics: L-Band Cavity FilterPass Band1525 - 1705 MHzInsertion Loss<= 1.0 dBPassband Ripple0.8 dBRejection50 dB @ > 1750 MHz and < 1000 MHzVSWR<= 1.20Impedance50 OhmsPower30 W average RF power (max)Temperature-10 to 50 CentigradeDimensions94x53x45 mmWeight200 gIP-RatingIP50

€64.26*
S-Band cavity filter 2170-2300 MHz
Data sheetThis is a cavity band-pass filter for the 2170-2300 MHz S-Band, particularly useful in satellite receiver applicationsYou can use it to attenuate any out-of-band interference while receiving only the wanted band. It will attenuate any transmissions from the nearby 2.1 GHz cellular band by >= 30 dB.Both connectors are SMA (female). It is not suitable for outdoor environments.It can support up to 30W of RF power and has the following characteristics: S-Band Cavity FilterPass Band2170 - 2300 MHzInsertion Loss<= 1.0 dBPassband Ripple0.8 dBRejection30 dB @ < 2160 MHzVSWR<= 1.30Impedance50 OhmsPower30 W average RF power (max)Temperature-20 to 50 CentigradeDimensions124x47x33 mmWeight186 gIP-RatingIP50

€65.45*
Quad-band omnidirectional SMA antenna for GSM
This is a small quad-band antenna with SMA connector, to be used for GSM Modems or picocells.

€5.95*
Tip
Quad-Band PCB Antenna 850/900/1800/1900MHz TE 1513259-1
This is a PCB antenna which can be soldered as SMT part on your custom circuit board.824 .. 960 MHz; 1710 - 1990 MHz50 Ohms impedance37.59 x 11.94 x 1.57 mmThis small embedded antenna provides the most reliable easy-to-use, and adjustment-free antenna technology for handling during assembly and implementation by developers.Minimum or no matching Specifications circuits required.Bandwidth and performance is dependent on ground plane size. Suggested minimum ground plane length from the antenna feed is 100 mm.PCB ground is to be on top layer.Product Homepage: https://www.te.com/usa-en/product-1513259-1.html

€0.83*
1800 MHz DCS / UMTS / LTE Band 3 duplexer 30W
Data sheetThis is a cavity duplexer for 1800 MHz DCS / UMTS / LTE Band 3 operation. You can use it to operate a GSM BTS (like our sysmoBTS) or any other BTS/NodeB/eNodeB with separate Rx and Tx ports at a single antenna.All connectors are SMA (female).It is not suitable for outdoor environments.It can support up to 30W of RF power and has the following characteristics:30 W DCS / UMTS / LTE Band 3 Duplexer TXRXPass Band1805 - 1880 MHz1710 - 1785 MHzInsertion Loss1.0 dB1.0 dBPassband Ripple0.8 dB0.8 dBRejection50 dB @ 80-850 MHz50 dB @ 1-3 GHz50 dB @ 80-800 MHz50dB @ 1-3 GHzReturn Lossminimum 20 dBImpedance50 OhmsPower30 W average RF powerTemperature-20 to 70 CentigradeDimensions192x60x47 mmWeight630 gIP-RatingIP50Order Codedx1800-kt30

€119.00*
SMA Attenuator, DC to 6 GHz, 500mW, 20dB
This is a SMA in-line (male-to-female) connectorized attenuator for 0-6GHzThe attenuator supports a maximum power of 500mW and is specified for 20 dB +/- 0.3dB over the temperature range of -45 to 100 centigrade.Ideal for use as component in RF networks for direct connection of phones to a BTS, without any air interface.

€24.99*
GPS antenna, 3m cable with SMA male connector
GPS antenna with 3m coaxial cable and SMA male connector.Suitable as accessory to a variety of sysmocom products, includingindoor sysmoBTS models with optional GPS receiverGPS receiver evaluation boardsicE1usb E1 interface with built-in GPS-DO

€20.23*
2600 MHz LTE Band 7 duplexer 30W
Data SheetThis is a cavity duplexer for 2600 MHz UMTS / LTE Band 7 operation. You can use it to operate a cellular base station with separate Rx and Tx ports at a single antenna.All connectors are SMA (female).It is not suitable for outdoor environments.It can support up to 30W of RF power and has the following characteristics:30 W Band 7 Duplexer TXRXPass Band2620 - 2690 MHz2500 - 2570 MHzInsertion Loss1.0 dB1.0 dBPassband Ripple0.8 dB0.8 dBRejection80 dB @ 2500 - 2570 MHz80dB @ 2620 - 2690 MHzReturn Lossminimum 18 dBImpedance50 OhmsPower30 W average RF powerTemperature-30 to 70 CentigradeDimensions192x88x47 mmWeight800 gIP-RatingIP50

€166.60*
SMA Terminator, 50 Ohms, 1W
This is a SMA (male) plug with integrated 50 Ohms resistive terminator.The terminator can sink up to 1W of RF power.Minimum return loss for GSM 850/900: 46 dB, for GSM 1800/1900: 39 dB.

€23.80*
16-channel GPS antenna splitter
BGT-KOH: Desktop Enclosure
In several use cases there is a need for providing a GPS reference signal to a variety of device with built-in receivers. Running separate Antenna cables to each of those GPS receivers is often difficult and cumbersome. This includes, for example lab setups where many cellular base stations with GPS clock reference input are operated lab setups wit a variety of measurement devices that utilized GPS disciplined reference clocks in-building distribution of GPS RF signals The sysmocom 16-channel GPS antenna RF splitter is the ideal solution for such setups. Its unparalleled number of 16 receiver-side RF ports allow for a large density of GPS receivers. The GPS RF signal of a single GPS antenna (which can optionally be phantom powered by the splitter) is filtered, amplified, filtered again and then split (in two stages of 1:4 dividers) across 16 RF outputs. Each output features an integrated DC-block and a dedicated LED to indicate if phantom voltage is supplied by the attached receiver or not. Supported biasing voltages on the output side are in the range of 3 .. 12V DC.The product is available in two form-factors a stand-alone extruded aluminum desktop enclosure - useful for portable operation on a lab desk as a module for a 3U component carrier - a perfect fit for larger rack-mounted lab installation or in-building GPS RF signal distribution Further LinksProduct HomepageData Sheet

Variants from €362.95*
€386.75*
SMA Attenuator, DC to 6 GHz, 500mW, 30dB
This is a SMA in-line (male-to-female) connectorized attenuator for 0-6GHzThe attenuator supports a maximum power of 500mW and is specified for 30 dB +/- 0.3dB over the temperature range of -45 to 100 centigrade.Ideal for use as component in RF networks for direct connection of phones to a BTS, without any air interface.

€29.75*
2100 MHz LTE Band 1 duplexer 30W
Data SheetThis is a cavity duplexer for 2100 MHz UMTS / LTE Band 1 operation. You can use it to operate a cellular base station with separate Rx and Tx ports at a single antenna.All connectors are SMA (female).It is not suitable for outdoor environments.It can support op to 30W of RF power and has the following characteristics:30 W Band 1 Duplexer TXRXPass Band2110 - 2170 MHz1920 - 1980 MHzInsertion Loss0.8 dB0.8 dBPassband Ripple0.6 dB0.6 dBRejection50 dB @ 2040 MHz80 dB @ 1920 - 1980 MHz50 dB @ 2040 MHz80dB @ 2110 - 2170 MHzReturn Lossminimum 18 dBImpedance50 OhmsPower30 W average RF powerTemperature-30 to 75 CentigradeDimensions192x60x47 mmWeight550 gIP-RatingIP50

€119.00*
800 MHz UMTS / LTE Band 20 duplexer 30W
Data SheetThis is a cavity duplexer for 800 MHz UMTS / LTE Band 20 operation. You can use it to operate a GSM BTS (like our sysmoBTS) with separate Rx and Tx ports at a single antenna.All connectors are SMA (female).It is not suitable for outdoor environments.30 W Band 20 Duplexer TXRXPass Band832 - 862 MHz791 - 821 MHzInsertion Loss1.2 dB1.2 dBPassband Ripple1.0 dB1.0 dBRejection63 dB @ 791-821 MHz63 dB @ 832-862 MHzReturn Lossminimum 18 dBImpedance50 OhmsPower30 W average RF powerTemperature-30 to 50 CentigradeDimensions192x98x47 mmWeight915 gIP-RatingIP50

€166.60*
Tip
900 MHz E-GSM / UMTS / LTE Band 8 duplexer 40W outdoor/IP67
Data SheetThis is a cavity duplexer for 900 MHz E-GSM / UMTS / LTE Band 8 operation. You can use it to operate a GSM BTS (like our sysmoBTS) or any other BTS/NodeB/eNodeB with separate Rx and Tx ports at a single antenna.All connectors are N (female).40 W E-GSM / Band 8 Duplexer (IP67) TXRXPass Band925 - 960 MHz880 - 915 MHzInsertion Loss1.0 dB1.0 dBPassband Ripple0.8 dB0.8 dBRejection60 dB @ 80-850 MHz60 dB @ 1-3 GHz60 dB @ 80-800 MHz60dB @ 1-3 GHzReturn Lossminimum 20 dBImpedance50 OhmsPower40 W average RF powerTemperature-20 to 65 CentigradeDimensions246x76x51 mmWeight1370 gIP-RatingIP67Order Codedx900-kt40-ip67

€178.50*
42.5dB IL resistive 1:4 RF splitter/combiner/attenuator PCBA, U.FL in, SMA out
This is a 1:4 resistive RF splitter/combiner with on-board additional per-port 30dB attenuation, resulting in total insertion loss of 42.5 dB.see the product homepage for more details, including the data sheet

€59.50*
900 MHz E-GSM / UMTS / LTE Band 8 duplexer 30W
Data SheetThis is a cavity duplexer for 900 MHz E-GSM / UMTS / LTE Band 8 operation. You can use it to operate a GSM BTS (like our sysmoBTS) or any other BTS/NodeB/eNodeB with separate Rx and Tx ports at a single antenna.All connectors are SMA (female).It is not suitable for outdoor environments.30 W E-GSM900 / Band 8 Duplexer TXRXPass Band925 - 960 MHz880 - 915 MHzInsertion Loss1.0 dB1.0 dBPassband Ripple0.8 dB0.8 dBRejection50 dB @ 80-850 MHz50 dB @ 1-3 GHz50 dB @ 80-800 MHz50 dB @ 1-3 GHzReturn Lossminimum 20 dBImpedance50 OhmsPower30 W average RF powerTemperature-20 to 70 CentigradeDimensions192x88x47 mmWeight815 gIP-RatingIP50

€178.50*
850 MHz GSM / UMTS / LTE Band 5 duplexer 30W
Data SheetThis is a cavity duplexer for 850 MHz GSM / UMTS / LTE Band 5 operation. You can use it to operate a GSM BTS (like our sysmoBTS) with separate Rx and Tx ports at a single antenna.All connectors are SMA (female).It is not suitable for outdoor environments.30 W GSM850 / Band 5 Duplexer TXRXPass Band869 - 894 MHz824 - 849 MHzInsertion Loss1.0 dB1.0 dBPassband Ripple0.2 dB0.2 dBRejection60 dB @ 80-850 MHz60 dB @ 1-3 GHz60 dB @ 80-800 MHz60 dB @ 1-3 GHzReturn Lossminimum 20 dBImpedance50 OhmsCoupling Port-30 dB (+/- 1.5 dB)Power30 W average RF powerTemperature-20 to 75 CentigradeDimensions166x102x36 mmWeight815 gIP-RatingIP50

€178.50*
16-channel GPS antenna splitter
BGT-KOH: 3U component carrier module
In several use cases there is a need for providing a GPS reference signal to a variety of device with built-in receivers. Running separate Antenna cables to each of those GPS receivers is often difficult and cumbersome. This includes, for example lab setups where many cellular base stations with GPS clock reference input are operated lab setups wit a variety of measurement devices that utilized GPS disciplined reference clocks in-building distribution of GPS RF signals The sysmocom 16-channel GPS antenna RF splitter is the ideal solution for such setups. Its unparalleled number of 16 receiver-side RF ports allow for a large density of GPS receivers. The GPS RF signal of a single GPS antenna (which can optionally be phantom powered by the splitter) is filtered, amplified, filtered again and then split (in two stages of 1:4 dividers) across 16 RF outputs. Each output features an integrated DC-block and a dedicated LED to indicate if phantom voltage is supplied by the attached receiver or not. Supported biasing voltages on the output side are in the range of 3 .. 12V DC.The product is available in two form-factors a stand-alone extruded aluminum desktop enclosure - useful for portable operation on a lab desk as a module for a 3U component carrier - a perfect fit for larger rack-mounted lab installation or in-building GPS RF signal distribution Further LinksProduct HomepageData Sheet

€362.95*
MS-147 plug to SMA female pigtail, 15cm
This is a 15cm pigtail cable from the MS-147 plug (male) to SMA bulkhead (female).MS-147 is the RF / antenna connector present on the Motorola/Compal C1xx phones. It's mostly useful if you want to connect the phone to a directional antenna, or measurement equipment like a MS tester.Please note that while this pigtail can be plugged into the MS-147 socket on the C1xx circuit board, the plug is not long enough to be used while the phone casing is closed!You will have to remove the phone casing or cut out a piece of plastic from the case.

€14.28*
osmo-bts-lna - 1800 MHz band uplink LNA kit
The osmo-bts-lna board is a low noise amplifier intended for DCS uplink reception (MS->BTS). This is DCS1800 for GSM and band 3 for both UMTS and LTE.The LNA features a 2-stage LNA formed by RF3865 (RFDM/Qorvo) and two EPCOS B3832 SAW.The board consumes about 200mA @5V. It intregrates a MIC5219-5 LDO and should be supplied with 5.5-12V DC (7V nom.), eitherby local connection (DC input), orby 'phantom power' via DC biasing from the RF output.The rf port is U.FL/IPEX by default and can be changed to sma by soldering sockets and moving a coupling capacitor.The osmo-bts-lna is delivered as a kit consisting of:* soldered pcb with all SMT components placed* shielding cage + cover placed on PCBA* U.FL/IPEX RF connectors placed* 2x 2pin 2.54mm DC through-hole header + pigtailATTENTION: This is kit. Some soldering is required! schematics + layout PDF renderings in osmocom wiki

€35.70*
1500 MHz GMR (Thuraya) duplexer 30W
Data sheetThis is a cavity duplexer for 1500 MHz GMR band operation. All connectors are SMA (female).It is not suitable for outdoor environments.It can support op to 30W of RF power and has the following characteristics:30 W GMR Duplexer TXRXPass Band1626 - 1661 MHz1518 - 1559 MHzInsertion Loss1.0 dB1.0 dBPassband Ripple1.0 dB1.0 dBIsolation Rx/Tx80 dB80 dBReturn Lossminimum 20 dBImpedance50 OhmsPower30 W average RF powerTemperature-20 to 70 CentigradeDimensions192x60x47 mmWeight640 gIP-RatingIP50

€119.00*